Vermont Castings RUVS40 Spezifikationen

1Vermont Castings RadianceTested and listed toANSI Z21.11.2b-1998, Unvented HeatersWARNING: Improper installa-tion, adjustment, alteration,service or

10Vermont Castings RadianceInstall Optional Fan, #2767/FK26Install the fan kit before the stove is connected to thegas line.The fan consists of a blow

11Vermont Castings Radiance5. Resecure the Rear Shroud panels.• Reinstall and tighten the two sheet metal screws(D, Fig. 10) that secure the inner an

12Vermont Castings RadianceConnect the Gas LineGas connection should be made in accordance with thecurrent edition of the National Fuel Gas Code, ANSI

13Vermont Castings RadianceInstall the LogsInstall the logs in sequence as shown below. The logset includes six sections: the rear log, left and right

14Vermont Castings Radiance4. Loosely sprinkle the lava rocks (#6) directly on topof the burner, between the front and middle logs. Donot place any em

15Vermont Castings RadianceOperationYour First FireRead these instructions carefully and familiarizeyourself with the burner controls of this heater.T

16Vermont Castings Radiance1. STOP! Read the safety information above on this panel.2. If applicable, turn thermostat to lowest setting or set burn

17Vermont Castings RadianceTrouble-WarningTurn OFF heater and allow to cool completelybefore servicing.ConditionNo spark at Pilot when Ignitor isopera

18Vermont Castings RadianceTroubleshooting (continued)ConditionPilot lights but Main Burner does notMain Burner shuts off and Pilot flamegoes out whil

19Vermont Castings RadianceMaintenanceYour Radiance Vent Free heater will provide years ofservice with minimal upkeep. The following procedureswill he

2Vermont Castings RadianceATTENTION CONSUMER:In order to ensure safe and effectiveinstallation, this unit must be installed only bya qualified agency,

20Vermont Castings RadianceCatalytic CombustorThe combustor should be cleaned annually to ensureoptimal performance. Follow the procedure below.Tools

21Vermont Castings RadianceItem/Model Number Part NumberRadiance Vent Free Gas Heater RUVS40Item/Model Number Part Number24320181960605452525556555653

22Vermont Castings Radiance21. Wire Clip 120861822. Wire Tie,Wire Harness/Rear Shroud 120150423. Wire Harness,Burner / Thermostat 160191324. Wire Harn

23Vermont Castings Radiance7. The Vermont Castings, Majestic Products Company shallhave no obligation to enhance or update any unit oncemanufactured.I

24Vermont Castings Radiance© The Vermont Castings, Majestic Products Company410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885www

3Vermont Castings RadianceFuel Type: NG LPManifold Pressure; Min. / Max.: 1.7"/3.5" 5.4"/11.0"Min. Inlet Supply Pressure foradjus

4Vermont Castings Radiance1. Install only in accordance with National Fuel GasCode, ANSI Z223.1 - latest edition. (Exception:Do not derate this applia

5Vermont Castings RadianceGeneral InformationVent Free FeaturesThe Radiance RUVS40 is an unvented gas heatingappliance tested and listed to the ANSI s

6Vermont Castings RadianceInstallation RequirementsTHIS HEATER MUST HAVE FRESH AIR FORPROPER OPERATION. IF NOT, POOR FUELCOMBUSTION COULD RESULT. READ

7Vermont Castings Radiance3. Add the BTU/Hr ratings of all fuel-burning appli-ances installed in the same space, including thefollowing:Gas Water Hea

8Vermont Castings RadianceA: Maximum Alcove Depth... 24" (609mm)B: To Side Wall... 4" (101mm)C

9Vermont Castings RadianceAssemblyRead these instructions thoroughly before startingthe assembly. Follow procedures in the ordergiven. Inspect the sto